Go to the game hall to play factory direct sale claw toy grabber machine. Do you "fail" countless times. Have you never experienced the joy of victory? Do you always complain that this is an impossible task? Maybe we can use some small skills. Let's get the doll. You can also do it in front of a female partner. After learning, practice, and then go to pick up my sister.

Basic tip 1: About clips

The clamps of factory direct sale claw toy grabber machine are generally composed of three. When grabbing dolls, the angle of claws is often inconsistent with the expectation. When the clip falls, one will fall on the doll or deviate from the grabbing point, so it is very important to turn the clip.

Turning the clip is actually very simple, that is, turning the joystick 360 degrees quickly, the clip will rotate and swing, and the angle will change. When the clip stops shaking, you can grab it, but pay attention to the time. It's fun to turn the clip, but don't get addicted. When I went to Wanda to play today, I found that the time of factory direct sale claw toy grabber machine reading seconds has become 15 seconds. It's depressed. It used to be 30 seconds...

Also, don't turn the clamp when it is on the side. It will knock on the glass of the machine, and the boss will stare at you.

Basic tip 2: About Buttons

Sometimes after reading the second, when the clip falls down by itself, it may be tighter and easier to catch the doll. (but I will use this method later, and I haven't caught it again.)

Another way of saying is to press the button to let the clip fall, and another press at the moment when the clip catches the doll will strengthen the claw force. To be specific, press or at 1 / 3 of the height of the doll just when it can hold the whole one. When the clip is completely in the end, the power of natural picking is usually not enough. Most machines with strong claw force press twice will be stronger, weak claw force press also useless. It's actually useful for some machines. It allows you to tighten your grip at the right time, making it easier to catch. But don't be excited. Press the second button early and the clip will be retracted in the middle of the air. Then the cup will come. I'm not responsible...

Practical skill 1: push down the doll

It's a very practical technology to push the doll down. For example, a bigger doll, or a two headed doll like a little bear and a little pig, it's better to grasp it from the body and neck of the doll. If you clip it from the head of the sitting doll, the grip has no grip point, and the doll is easy to fall off. If you really like this doll, I suggest that you pay two coins for bedding first, and then you can put it down and catch it.

The method is very simple, that is, the clip falls a little bit, let one claw top the head of the doll, and the other two claws grasp the body of the doll obliquely, and the doll will be pulled down after the clip is retracted.

Pay attention to the position. You can use the rotating clip. Besides, if there are too many obstacles around the doll, this doesn't apply.

Practical skill 2: swing the clamp

This method is more difficult, my hands are more stupid, always unsuccessful. First, the target doll should not be too close to the glass or the acrylic at the exit, or it will be knocked by the clip. After confirming that there is no obstacle next to the target doll, swing the clip left and right to make the clip swing sharply left and right. Press the drop button when the opportunity is right. When the claw is caught by the doll and retracted, the doll will be thrown to the exit.

Pay attention to the calculation of the falling position of the clip. After the doll is clamped, the clip will not relax at this time. When the clip is retracted, it will swing. When it reaches the top, the clip will generally release, but our doll will also be thrown to the hole. This method sounds very good. It's much safer than the clip moving slowly, but it's hard to aim, so the success rate is not high. RP is very important.

Practical skill 3: roll into the hole

This method is to let the doll clip up and fall, and then directly roll into the hole. This method is very simple, but it needs to be observed first. Generally speaking, it is easier to roll in when the slope is more than 45 degrees, and it is more difficult when the slope is less than 30 degrees. The method is that when the clip falls, it should not be in a vertical line with the doll, and the clip should be a little closer to the hole, so that when the clip is recycled, there will be a pull to the exit.

This method is suitable for the machine with low height of the hole stop. It's better to be a machine with more dolls. If you have more money, it will be easier for you to clamp a few to fill the hole first, then roll or push with the last method. If you can't let the child cover the wolf, you need to make some bedding first, or you need to harvest a little bit more than if you always clamp.

Summary of experience

The above are several specific methods, but also some simple methods. It can let a hook pass through a certain part of the doll, such as tag, rope, doll's clothes, etc., which has a high probability. If the doll is caught on the hook, don't worry. Call the clerk. The doll is yours.